Altera RapidIO II MegaCore Function Manual de usuario Pagina 37
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3: Parameter Settings 3–7
Capability Registers Settings
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
Assembly Vendor ID
Assembly Vendor ID uniquely identifies the vendor who manufactured the
assembly. This value corresponds to the
AssyVendorIdentity
field of the
Assembly
Identity
register.
Assembly Information CAR
The Assembly Information CAR options identify the vendor who manufactured the
assembly or subsystem of the device and the pointer to the first entry in the Extended
Features list, and sets these values in the
Assembly
Information
(Table 6–25) CAR.
Revision ID
Revision ID indicates the revision level of the assembly and sets the
AssyRev
field of
the
Assembly
Information
CAR (Table 6–25). In the Qsys design flow, this parameter
is labeled Assembly revision ID.
Processing Element Features CAR
The
Processing Element
Features
CAR (Table 6–26 on page 6–27) identifies the
major features of the processing element.
Bridge Support
Bridge support, when turned on, sets the
Bridge
bit in the
Processing
Element
Features
CAR and indicates that this processing element can bridge to another
interface such as PCI Express, a proprietary processor bus such as Avalon-MM,
DRAM, or other interface.
Memory Access
Memory access, when turned on, sets the
Memory
bit in the
Processing
Element
Features
CAR and indicates that the processing element has physically addressable
local address space that can be accessed as an endpoint through non-maintenance
operations. This local address space may be limited to local configuration registers, or
can be on-chip SRAM, or another memory device.
Processor Present
Processor present, when turned on, sets the
Processor
bit in the
Processing
Element
Features
CAR and indicates that the processing element physically contains a local
processor such as the Nios
®
II embedded processor or similar device that executes
code. A device that bridges to an interface that connects to a processor should set the
Bridge
bit—as described in “Bridge Support”—instead of the
Processor
bit.
Enable Flow Arbitration Support
Enable flow arbitration support, when turned on, sets the
Flow Arbitration
Support
bit in the
Processing
Element
Features
CAR and indicates that the
processing element supports flow arbitration. The IP core routes Type 7 packets to the
Avalon-ST pass-through interface, so user logic must implement flow control on the
Avalon-ST pass-through interface.
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Relacionado con productos y manuales para Instrumentos de medición Altera RapidIO II MegaCore Function
Instrumentos de medición Altera SerialLite III Streaming MegaCore Function Manual de usuario
(68 paginas)
(68 paginas)
Instrumentos de medición Altera Signal Integrity Development Kit, Stratix V GX Edi Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales