Altera RapidIO II MegaCore Function Manual de usuario Pagina 207
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
August 2014 Altera Corporation RapidIO II MegaCore Function
User Guide
A. Initialization Sequence
This appendix describes the most basic initialization sequence for a RapidIO system
that contains two RapidIO IP cores connected through their RapidIO interfaces.
To initialize the system, perform these steps:
1. Read the
Port 0 Error and Status Command and Status
register (CSR) (
0x00158
)
of the first RapidIO II IP core to confirm port initialization.
2. Set the following registers in the first RapidIO II IP core:
a. To set the base ID of the device to
0x01
, set the
Base_deviceID
field (bits 23:16)
or the
Large_base_deviceID
field (bits 15:0) of the
Base Device ID
register
(
0x00060
) to
0x1
.
b. To allow request packets to be issued, write
1
to the
ENA
field (bit 30) of the
Port
General Control CSR
(
0x13C
).
c. To set the destination ID of outgoing maintenance request packets to
0x02
, set
the
DESTINATION_ID
field (bits 23:16) or the combined {
LARGE_DESTINATION_ID
(MSB)
,
DESTINATION_ID
} fields (bits 31:16) of the
Tx Maintenance Window 0
Control
register (
0x1010C
) to
0x02
.
d. To enable an all-encompassing address mapping window for the maintenance
module, write
1’b1
to the
WEN
field (bit 2) of the
Tx Maintenance Window 0
Mask
register (
0x10104
).
3. Set the following registers in the second RapidIO II IP core:
a. To set the base ID of the device to
0x02
, set the
Base_deviceID
field (bits 23:16)
or the
Large_base_deviceID
field (bits 15:0) of the
Base Device ID
register
(
0x00060
) to
0x02
.
b. To allow request packets to be issued, write
1’b1
to the
ENA
field (bit 30) of the
Port General Control CSR
(
0x13C
).
c. To set the destination ID of outgoing maintenance packets to
0x0
, set the
DESTINATION_ID
field (bits 23:16) or the combined {
LARGE_DESTINATION_ID
(MSB)
,
DESTINATION_ID
} fields (bits 31:16) of the
Tx Maintenance Window 0
Control
register (
0x1010C
) to
0x0
.
d. To enable an all-encompassing address mapping window for the maintenance
module, write
1’b1
to the
WEN
field (bit 2) of the
Tx Maintenance Window 0
Mask
register (
0x10104
).
These register settings allow one RapidIO II IP core to remotely access the other
RapidIO II IP core.
To access the registers, the system requires an Avalon-MM master, for example a
Nios II processor. The Avalon-MM master can program these registers.
You can use the Qsys system integration tool, available with the Quartus II software,
to rapidly and easily build and evaluate your RapidIO system.
- User Guide 1
- RapidIO II MegaCore Function 1
- Contents 3
- Contents v 5
- Chapter 5. Signals 6
- Chapter 6. Software Interface 6
- Chapter 7. Testbench 6
- 1. About The RapidIO II 9
- MegaCore Function 9
- Releases 10
- RapidIO II IP Core Features 10
- Features 11
- Device Family Support 12
- IP Core Verification 13
- Hardware Testing 14
- Interoperability Testing 14
- Note to Table 1–3: 16
- Notes to Table 1–4: 16
- Installation and Licensing 17
- 2. Getting Started 19
- Simulating IP Cores 22
- Transceiver Settings 26
- External Transceiver PLL 26
- 3. Parameter Settings 31
- Note to Table 3–1: 32
- Enable 16-Bit Device ID Width 33
- Logical Layer Settings 34
- Capability Registers Settings 35
- Device ID 36
- Vendor ID 36
- Revision ID 36
- Assembly ID 36
- Assembly Information CAR 37
- Enable Flow Control Support 38
- Enable Switch Support 38
- Number of Ports 38
- Port Number 39
- Maximum PDU 39
- Destination Operations CAR 40
- Port General Control CSR 40
- Port 0 Control CSR 41
- Lane n Status 0 CSR 41
- Extended Features Pointer CSR 41
- 4. Functional Description 43
- Note to Table 4–2: 44
- Clocking and Reset Structure 45
- Notes to Table 4–3: 46
- RapidIO II 47
- Transactions 55
- Notes to Table 4–6: 57
- Notes to Table 4–7: 59
- Note to Table 4–8: 59
- Note to Figure 4–9: 66
- Note to Table 4–10: 70
- Notes to Table 4–11: 71
- Table 6–60 on page 6–40 72
- Note to Table 4–12: 73
- Maintenance Module 74
- Maintenance Interface Signals 75
- Doorbell Module Block Diagram 86
- Preserving Transaction Order 87
- Doorbell Module Signals 88
- Generating a Doorbell Message 88
- Receiving a Doorbell Message 89
- Transaction ID Ranges 90
- Notes to Table 4–24: 92
- Note to Table 4–26: 94
- Note to Table 4–27: 95
- field 97
- User Receiving Write Request 100
- Logical Layer Interfaces 101
- Transport Layer 112
- Receiver 113
- Transmitter 114
- Physical Layer 115
- Physical Layer Interfaces 116
- Low-level Interface Receiver 116
- CRC Checking and Removal 117
- Protocol Violations 119
- Fatal Errors 119
- Maintenance Avalon-MM Slave 120
- Maintenance Avalon-MM Master 121
- Port-Write Reception Module 122
- Input/Output Avalon-MM Slave 122
- Input/Output Avalon-MM Master 123
- 5. Signals 125
- Physical Layer Signals 126
- Low Latency Signals 127
- Multicast Event Signals 128
- Chapter 5: Signals 5–5 129
- Note to Table 5–7: 130
- Chapter 5: Signals 5–7 131
- 5–8 Chapter 5: Signals 132
- Register-Related Signals 133
- Avalon-MM Interface Signals 133
- Note to Table 5–12: 134
- Chapter 5: Signals 5–11 135
- Note to Table 5–15: 136
- Error Reporting Signals 137
- 5–14 Chapter 5: Signals 138
- 6. Software Interface 139
- Memory Map 140
- Physical Layer Registers 144
- Note to Table 6–9: 147
- Note to Table 6–14: 154
- Note to Table 6–15: 158
- Note to Table 6–17: 160
- Note to Table 6–22: 164
- Note to Table 6–23: 164
- Note to Table 6–24: 165
- Note to Table 6–25: 165
- Note to Table 6–26: 166
- Note to Table 6–27: 167
- Notes to Table 6–28: 168
- Notes to Table 6–29: 169
- Note to Table 6–30: 169
- Note to Table 6–31: 169
- Notes to Table 6–32: 170
- Note to Table 6–34: 171
- Note to Table 6–35: 171
- Note to Table 6–36: 172
- Note to Table 6–37: 172
- Transmit Port-Write Registers 174
- Receive Port-Write Registers 175
- Note to Table 6–59: 178
- Error Management Registers 180
- Note to Table 6–66: 181
- Notes to Table 6–67: 183
- Notes to Table 6–70: 185
- Notes to Table 6–71: 185
- Doorbell Message Registers 191
- Note to Table 6–89: 193
- 7. Testbench 195
- 7–2 Chapter 7: Testbench 196
- Testbench Overview 196
- Testbench Sequence 197
- 7–4 Chapter 7: Testbench 198
- Chapter 7: Testbench 7–5 199
- SWRITE Transactions 200
- NREAD Transactions 200
- NWRITE_R Transactions 201
- NWRITE Transactions 202
- Doorbell Transactions 202
- Port-Write Transactions 203
- Testbench Completion 204
- Chapter 7: Testbench 7–11 205
- 7–12 Chapter 7: Testbench 206
- A. Initialization Sequence 207
- MegaCore Function v12.1 209
- Additional Information 213
- Info–2 Additional Information 214
- Document Revision History 214
- Additional Information Info–3 215
- Info–4 Additional Information 216
- Note to Table: 217
- Info–6 Additional Information 218
- Typographic Conventions 218
Relacionado con productos y manuales para Instrumentos de medición Altera RapidIO II MegaCore Function
Instrumentos de medición Altera SerialLite III Streaming MegaCore Function Manual de usuario
(68 paginas)
(68 paginas)
Instrumentos de medición Altera Signal Integrity Development Kit, Stratix V GX Edi Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales