Altera Transceiver PHY IP Core Manual de usuario Pagina 587
- Pagina / 702
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Signal Name Direction Clock Domain Description
rx_digital-
reset[<n> -1:0]
Output Synchronous to the
Transceiver PHY
Reset Controller
input clock.
Digital reset for RX. The width of this signal
depends on the number of channels. This signal
is asserted when any of the following
conditions is true:
• reset is asserted
• rx_analogreset is asserted
• rx_cal_busy is asserted
• rx_is_lockedtodata is deasserted and rx_
manual is deasserted
When all of these conditions are false, the reset
counter begins its countdown for deassertion of
rx_digitalreset.
rx_analogreset
[<n>-1:0]
Output Synchronous to the
Transceiver PHY
Reset Controller
input clock.
Analog reset for RX. When asserted, resets the
RX CDR and the RX PMA blocks of the
transceiver PHY. This signal is asserted when
any of the following conditions is true:
• reset is asserted
• rx_cal_busy is asserted
The width of this signal depends on the number
of channels.
rx_ready[<n>-1:0] Output Synchronous to the
Transceiver PHY
Reset Controller
input clock.
Status signal to indicate when the RX reset
sequence is complete. This signal is deasserted
while the RX reset is active. It is asserted a few
clock cycles after the deassertion of rx_
digitalreset. Some protocol implementa‐
tions may require you to monitor this signal
prior to sending data. The width of this signal
depends on the number of RX channels.
pll_powerdown[<p>-
1:0]
Output Synchronous to the
Transceiver PHY
Reset Controller
input clock.
Asserted to power down a transceiver PLL
circuit. When asserted, the selected TX PLL is
reset.
Timing Constraints for Bonded PCS and PMA Channels
For designs that use bonded TX PCS and PMA channels, the digital reset signal to all TX channels within
a bonded group must meet a maximum skew tolerance imposed by physical routing. This skew tolerance
is one-half the TX parallel clock cycle (tx_clkout). This requirement is not necessary for bonded TX
PMA-only channels or for RX PCS channels.
17-10
Timing Constraints for Bonded PCS and PMA Channels
UG-01080
2015.01.19
Altera Corporation
Transceiver PHY Reset Controller IP Core
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Native Transceiver PHYs 12
- Transceiver PHY Modules 15
- Resetting the Transceiver PHY 16
- File Name Description 18
- Unsupported Features 20
- Getting Started Overview 21
- Design Flows 22
- Specifying Parameters 23
- Simulate the IP Core 24
- 10GBASE-R PHY IP Core 25
- Arria V GT 10GBASE-R 27
- Transceiver Protocol 28
- General Option Parameters 33
- 10GBASE-R PHY Interfaces 37
- 10GBASE-R PHY Data Interfaces 38
- Reset Control and Power Down 46
- Signal Name Directio 53
- 1588 Delay Requirements 54
- 10GBASE-R Parameters 63
- Reconfig 67
- 10BASE-KR PHY Interfaces 75
- Daisy-Chain Interface Signals 83
- Bit R/W Name Description 100
- PMA Registers 103
- PCS Registers 104
- Creating a 10GBASE-KR Design 105
- Editing a 10GBASE-KR MIF File 106
- Send Feedback 107
- Design Example 108
- SDC Timing Constraints 109
- Acronyms 109
- UG-01080 110
- Subscribe 110
- Related Information 111
- Item Description 111
- Device Family Support 112
- 1GbE Parameters 113
- Speed Detection Parameters 114
- PHY Analog Parameters 115
- 1G/10GbE PHY Interfaces 116
- 2015.01.19 117
- 1G/10GbE PHY Data Interfaces 118
- Serial Data Interface 121
- Register Interface Signals 123
- Addr Bit R/W Name Description 124
- 1G/10 GbE GMII PCS Registers 127
- Cntl & 131
- Editing a 1G/10GbE MIF File 132
- Creating a 1G/10GbE Design 133
- Simulation Support 139
- TimeQuest Timing Constraints 139
- WAN Wide Area Network 140
- XAUI PHY IP Core 141
- XAUI PHY Release Information 142
- Stratix V Devices 143
- Parameterizing the XAUI PHY 143
- XAUI PHY General Parameters 144
- Name Value Description 145
- XAUI PHY Analog Parameters 146
- Advanced Options Parameters 148
- XAUI PHY Configurations 149
- XAUI PHY Ports 150
- XAUI PHY Data Interfaces 151
- SDR XGMII TX Interface 152
- SDR XGMII RX Interface 153
- XAUI Hard IP Core 154
- Hard PCS 154
- Soft PCS 154
- Name Direction Description 157
- Interlaken PHY IP Core 168
- Parameter Value Description 170
- Interlaken PHY Interfaces 173
- Interlaken PHY PLL Interface 181
- Preset C 198
- PHY for PCIe (PIPE) Clocks 201
- Signal Name 202
- Direction Signal Name 202
- PHY IP Core for PCI Express 204
- Hard PCS and PMA 204
- Phase 2 (Optional) 210
- Phase 3 (Optional) 211
- Custom PHY IP Core 214
- Parameterizing the Custom PHY 216
- Word Alignment Parameters 220
- Rate Match FIFO Parameters 222
- Byte Order Parameters 224
- Analog Parameters 229
- Presets for Ethernet 229
- Interfaces 232
- Configuration Bus Used Bits 234
- Clock Interface 236
- Optional Status Interface 237
- Custom PHY PCS and PMA 241
- Custom PHY IP Core Registers 242
- Reset Controls –Manual Mode 243
- Custom PCS 245
- Dynamic Reconfiguration 246
- Low Latency PHY IP Core 248
- General Options Parameters 251
- Additional Options Parameters 254
- TX PLL (0–3) 258
- (Refer to 258
- Channel Interface 259
- Low Latency PHY Interfaces 260
- PMA and Light-Weight PCS 264
- Data Rate (Mbps) 270
- TX_tc lock_output 273
- PDI O >R X_ deser 273
- Serial Data Rate (Mbps) 277
- Single-Width Double-Width 277
- 8-Bit 16-Bit 16-Bit 32-Bit 277
- TX Data Word Description 285
- RX Data Word Description 286
- Deterministic PHY IP Core 291
- Parameter Presets 301
- Name Range Description 302
- Parameter Range Description 304
- PATTERN POLYNOMIAL 323
- PCS-PMA Width 323
- 8-Bit 10-Bit 16-Bit 20-Bit 323
- 10G PCS Pattern Generators 340
- Native PHY Common Interfaces 345
- Standard PCS Interface Ports 351
- Name Dir Synchronous to 353
- Description 353
- 10G PCS Interface 356
- 10G PCS Interface Ports 357
- ×6/×N Bonded Clocking 367
- Transceiver Bank 368
- Slew Rate Settings 374
- General Parameters 378
- PMA Parameters 379
- TX PMA Parameters 380
- TX PLL Parameters 381
- RX PMA Parameters 383
- Standard PCS Parameters 385
- Phase Compensation FIFO 387
- Rate Match FIFO 390
- Overview 484
- Cyclone Device Family Support 485
- Altera V-Series FPGA 520
- Utilization 522
- Embedded 529
- Controller 529
- Offset Cancellation 530
- Duty Cycle Calibration 530
- EyeQ Usage Example 536
- Turning on Triggered DFE Mode 540
- Channel Reconfiguration 550
- PLL Reconfiguration 550
- MIF Generation 554
- MIF Format 555
- Reduced MIF Creation 559
- Register-Based Read 560
- Direct Write Reconfiguration 561
- Reconfiguration 565
- Loopback Modes 575
- Transceiver 576
- Transceiver PHY Instance 579
- Transceiver PHY 579
- Reset Controller 579
- Transceiver PLL Parameters 592
- Transceiver PLL Signals 593
- XCVR_IO_PIN_TERMINATION 596
- XCVR_REFCLK_PIN_TERMINATION 597
- XCVR_TX_SLEW_RATE_CTRL 597
- XCVR_VCCR_ VCCT_VOLTAGE 598
- CDR_BANDWIDTH_PRESET 598
- PLL_BANDWIDTH_PRESET 599
- XCVR_RX_DC_GAIN 599
- XCVR_ANALOG_SETTINGS_PROTOCOL 599
- XCVR_RX_COMMON_MODE_VOLTAGE 600
- XCVR_RX_SD_ENABLE 601
- XCVR_RX_SD_OFF 601
- XCVR_RX_SD_ON 602
- XCVR_RX_SD_THRESHOLD 602
- XCVR_TX_COMMON_MODE_VOLTAGE 603
- XCVR_TX_PRE_EMP_1ST_POST_TAP 603
- XCVR_TX_RX_DET_ENABLE 603
- XCVR_TX_RX_DET_MODE 604
- XCVR_TX_VOD 604
- XCVR_TX_VOD_PRE_EMP_CTRL_SRC 604
- XCVR_RX_BYPASS_EQ_STAGES_234 606
- XCVR_VCCA_VOLTAGE 607
- XCVR_VCCR_VCCT_VOLTAGE 608
- XCVR_TX_PRE_EMP_PRE_TAP_USER 615
- XCVR_TX_PRE_EMP_2ND_POST_TAP 616
- XCVR_TX_PRE_EMP_INV_2ND_TAP 616
- XCVR_TX_PRE_EMP_INV_PRE_TAP 617
- XCVR_TX_PRE_EMP_PRE_TAP 617
- XCVR_TX_RX_DET_OUTPUT_SEL 618
- XCVR_GT_IO_PIN_TERMINATION 628
- XCVR_GT_RX_DC_GAIN 635
- XCVR_GT_RX_CTLE 636
- XCVR_GT_TX_PRE_EMP_ PRE_TAP 638
- XCVR_GT_TX_VOD_MAIN_TAP 638
- Transceivers 648
- 2013.12.20 650
- Stratix IV GX Devices 651
- Parameter Name 653
- Comments 653
- Custom PHY Width 659
- Chapter Document 661
- Changes Made 661
- Date Document 676
- How to Contact Altera 702
Relacionado con productos y manuales para Instrumentos de medición Altera Transceiver PHY IP Core
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales