Clocks
Frame
Generator
TX FIFO
RX FIFO
Block
Synchronizer
Frame
Synchronizer
Bit-Slip
Gearbox
Feature
64B/66B
BER
10G PCS Interface Ports
CRC32
tx_10g_coreclkin[<n>-1:0]
rx_10g_coreclkin[<n>-1:0]
tx_10g_clkout[<n>-1:0]
rx_10g_clkout[<n>-1:0]
rx_10g_clk33out[<n>-1:0]t
tx_10g_control[8<n>-1:0]
tx_10g_data_valid[<n>-1:0]
tx_10g_fifo_full[<n>-1:0]
tx_10g_fifo_pfull[<n>-1:0]
tx_10g_fifo_empty[<n>-1:0]
tx_10g_fifo_pempt[<n>-1:0]y
tx_10g_fifo_del[<n>-1:0]
tx_10g_fifo_insert[<n>-1:0]
rx_10g_control[10<n>-1:0]
rx_10g_fifo_rd_en[<n>-1:0]
rx_10g_data_valid[<n>-1:0]
rx_10g_fifo_full[<n>-1:0]
rx_10g_fifo_pfull[<n>-1:0]
rx_10g_fifo_empty[<n>-1:0]
rx_10g_fifo_pempty[<n>-1:0]
rx_10g_fifo_align_clr[<n>-1:0]
rx_10g_fifo_align_en[<n>-1:0]
rx_10g_align_val[<n>-1:0]
rx_10g_fifo_del[<n>-1:0]
rx_10g_fifo_insert[<n>-1:0]
rx_10g_crc32err[<n>-1:0]
tx_10g_diag_status[2<n>-1:0]
tx_10g_burst_en[<n>-1:0]
tx_10g_frame[<n>-1:0]
rx_10g_frame[<n>-1:0]
rx_10g_frame_lock[<n>-1:0]
rx_10g_pyld_ins[<n>-1:0]
rx_10g_frame_mfrm_err[<n>-1:0]
rx_10g_frame_sync_err[<n>-1:0]
rx_10g_scram_err[<n>-1:0]
rx_10g_frame_skip_ins[<n>-1:0]
rx_10g_frame_skip_err[<n>-1:0]
rx_10g_frame_diag_err[<n>-1:0]
rx_10g_frame_diag_status[2<n>-1:0]
rx_10g_blk_lock[<n>-1:0]
rx_10g_blk_sh_err[<n>-1:0]
rx_10g_bitslip[<n>-1:0]
tx_10g_bitslip[7<n>-1:0]
rx_10g_clr_errblk_count[<n>-1:0]
rx_10g_highber[<n>-1:0]
rx_10g_clr_highber_cnt[<n>-1:0]
PRBS
rx_10g_prbs_done
rx_10g_prbs_err
rx_10g_prbs_err_clr
The following table describes the signals available for the 10G PCS datapath. When you enable both the
PHY.
The signals in the following table are shown when the Phase Compensation FIFO is used in FIFO mode.
FIFO.
FIFO. .
Comentarios a estos manuales