Altera Transceiver PHY IP Core Manual de usuario Pagina 229
- Pagina / 702
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Name Value Description
Enable channel interface On/Off Turn this option on to enable PLL and
datapath dynamic reconfiguration. When you
select this option, the width of tx_parallel_
data and rx_parallel_data buses increases
in the following way.
• n The tx_parallel_data bus is 44 bits
per lane; however, only the low-order
number of bits specified by the FPGA
fabric transceiver interface width contain
valid data for each lane.
• n The rx_parallel_data bus is 64 bits
per lane; however, only the low-order
number of bits specified by the FPGA
fabric transceiver interface width contain
valid data.
Related Information
General Options Parameters on page 9-3
Analog Parameters
Click the appropriate link to specify the analog options for your device:
Related Information
• Analog Settings for Arria V Devices on page 19-2
• Analog Settings for Arria V GZ Devices on page 19-11
• Analog Settings for Cyclone V Devices on page 19-26
• Analog Settings for Stratix V Devices on page 19-34
Presets for Ethernet
Presets allow you to specify a group of parameters to implement a particular protocol or application. If
you apply the presets for GIGE-1.25 Gbps or GIGE–2.5 Gbps, parameters with specific required values for
those protocols are set for you. Selecting a preset does not prevent you from changing any parameter to
meet the requirements of your design.
Table 9-11: Presets for Ethernet Protocol
Parameter Name GIGE-1.25 Gbps GIGE-2.50 Gbps
General Options Tab
Parameter validation rules GIGE GIGE
Enable bonding Off Off
FPGA fabric transceiver interface
width
8 16
9-16
Analog Parameters
UG-01080
2015.01.19
Altera Corporation
Custom PHY IP Core
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Altera Corporation 10
- Native Transceiver PHYs 12
- Transceiver PHY Modules 15
- Resetting the Transceiver PHY 16
- File Name Description 18
- Unsupported Features 20
- Getting Started Overview 21
- Design Flows 22
- Specifying Parameters 23
- Simulate the IP Core 24
- 10GBASE-R PHY IP Core 25
- Arria V GT 10GBASE-R 27
- Transceiver Protocol 28
- General Option Parameters 33
- 10GBASE-R PHY Interfaces 37
- 10GBASE-R PHY Data Interfaces 38
- Reset Control and Power Down 46
- Signal Name Directio 53
- 1588 Delay Requirements 54
- 10GBASE-R Parameters 63
- Reconfig 67
- 10BASE-KR PHY Interfaces 75
- Daisy-Chain Interface Signals 83
- Bit R/W Name Description 100
- PMA Registers 103
- PCS Registers 104
- Creating a 10GBASE-KR Design 105
- Editing a 10GBASE-KR MIF File 106
- Send Feedback 107
- Design Example 108
- SDC Timing Constraints 109
- Acronyms 109
- UG-01080 110
- Subscribe 110
- Related Information 111
- Item Description 111
- Device Family Support 112
- 1GbE Parameters 113
- Speed Detection Parameters 114
- PHY Analog Parameters 115
- 1G/10GbE PHY Interfaces 116
- 2015.01.19 117
- 1G/10GbE PHY Data Interfaces 118
- Serial Data Interface 121
- Register Interface Signals 123
- Addr Bit R/W Name Description 124
- 1G/10 GbE GMII PCS Registers 127
- Cntl & 131
- Editing a 1G/10GbE MIF File 132
- Creating a 1G/10GbE Design 133
- Simulation Support 139
- TimeQuest Timing Constraints 139
- WAN Wide Area Network 140
- XAUI PHY IP Core 141
- XAUI PHY Release Information 142
- Stratix V Devices 143
- Parameterizing the XAUI PHY 143
- XAUI PHY General Parameters 144
- Name Value Description 145
- XAUI PHY Analog Parameters 146
- Advanced Options Parameters 148
- XAUI PHY Configurations 149
- XAUI PHY Ports 150
- XAUI PHY Data Interfaces 151
- SDR XGMII TX Interface 152
- SDR XGMII RX Interface 153
- XAUI Hard IP Core 154
- Hard PCS 154
- Soft PCS 154
- Name Direction Description 157
- Interlaken PHY IP Core 168
- Parameter Value Description 170
- Interlaken PHY Interfaces 173
- Interlaken PHY PLL Interface 181
- Preset C 198
- PHY for PCIe (PIPE) Clocks 201
- Signal Name 202
- Direction Signal Name 202
- PHY IP Core for PCI Express 204
- Hard PCS and PMA 204
- Phase 2 (Optional) 210
- Phase 3 (Optional) 211
- Custom PHY IP Core 214
- Parameterizing the Custom PHY 216
- Word Alignment Parameters 220
- Rate Match FIFO Parameters 222
- Byte Order Parameters 224
- Analog Parameters 229
- Presets for Ethernet 229
- Interfaces 232
- Configuration Bus Used Bits 234
- Clock Interface 236
- Optional Status Interface 237
- Custom PHY PCS and PMA 241
- Custom PHY IP Core Registers 242
- Reset Controls –Manual Mode 243
- Custom PCS 245
- Dynamic Reconfiguration 246
- Low Latency PHY IP Core 248
- General Options Parameters 251
- Additional Options Parameters 254
- TX PLL (0–3) 258
- (Refer to 258
- Channel Interface 259
- Low Latency PHY Interfaces 260
- PMA and Light-Weight PCS 264
- Data Rate (Mbps) 270
- TX_tc lock_output 273
- PDI O >R X_ deser 273
- Serial Data Rate (Mbps) 277
- Single-Width Double-Width 277
- 8-Bit 16-Bit 16-Bit 32-Bit 277
- TX Data Word Description 285
- RX Data Word Description 286
- Deterministic PHY IP Core 291
- Parameter Presets 301
- Name Range Description 302
- Parameter Range Description 304
- PATTERN POLYNOMIAL 323
- PCS-PMA Width 323
- 8-Bit 10-Bit 16-Bit 20-Bit 323
- 10G PCS Pattern Generators 340
- Native PHY Common Interfaces 345
- Standard PCS Interface Ports 351
- Name Dir Synchronous to 353
- Description 353
- 10G PCS Interface 356
- 10G PCS Interface Ports 357
- ×6/×N Bonded Clocking 367
- Transceiver Bank 368
- Slew Rate Settings 374
- General Parameters 378
- PMA Parameters 379
- TX PMA Parameters 380
- TX PLL Parameters 381
- RX PMA Parameters 383
- Standard PCS Parameters 385
- Phase Compensation FIFO 387
- Rate Match FIFO 390
- Overview 484
- Cyclone Device Family Support 485
- Altera V-Series FPGA 520
- Utilization 522
- Embedded 529
- Controller 529
- Offset Cancellation 530
- Duty Cycle Calibration 530
- EyeQ Usage Example 536
- Turning on Triggered DFE Mode 540
- Channel Reconfiguration 550
- PLL Reconfiguration 550
- MIF Generation 554
- MIF Format 555
- Reduced MIF Creation 559
- Register-Based Read 560
- Direct Write Reconfiguration 561
- Reconfiguration 565
- Loopback Modes 575
- Transceiver 576
- Transceiver PHY Instance 579
- Transceiver PHY 579
- Reset Controller 579
- Transceiver PLL Parameters 592
- Transceiver PLL Signals 593
- XCVR_IO_PIN_TERMINATION 596
- XCVR_REFCLK_PIN_TERMINATION 597
- XCVR_TX_SLEW_RATE_CTRL 597
- XCVR_VCCR_ VCCT_VOLTAGE 598
- CDR_BANDWIDTH_PRESET 598
- PLL_BANDWIDTH_PRESET 599
- XCVR_RX_DC_GAIN 599
- XCVR_ANALOG_SETTINGS_PROTOCOL 599
- XCVR_RX_COMMON_MODE_VOLTAGE 600
- XCVR_RX_SD_ENABLE 601
- XCVR_RX_SD_OFF 601
- XCVR_RX_SD_ON 602
- XCVR_RX_SD_THRESHOLD 602
- XCVR_TX_COMMON_MODE_VOLTAGE 603
- XCVR_TX_PRE_EMP_1ST_POST_TAP 603
- XCVR_TX_RX_DET_ENABLE 603
- XCVR_TX_RX_DET_MODE 604
- XCVR_TX_VOD 604
- XCVR_TX_VOD_PRE_EMP_CTRL_SRC 604
- XCVR_RX_BYPASS_EQ_STAGES_234 606
- XCVR_VCCA_VOLTAGE 607
- XCVR_VCCR_VCCT_VOLTAGE 608
- XCVR_TX_PRE_EMP_PRE_TAP_USER 615
- XCVR_TX_PRE_EMP_2ND_POST_TAP 616
- XCVR_TX_PRE_EMP_INV_2ND_TAP 616
- XCVR_TX_PRE_EMP_INV_PRE_TAP 617
- XCVR_TX_PRE_EMP_PRE_TAP 617
- XCVR_TX_RX_DET_OUTPUT_SEL 618
- XCVR_GT_IO_PIN_TERMINATION 628
- XCVR_GT_RX_DC_GAIN 635
- XCVR_GT_RX_CTLE 636
- XCVR_GT_TX_PRE_EMP_ PRE_TAP 638
- XCVR_GT_TX_VOD_MAIN_TAP 638
- Transceivers 648
- 2013.12.20 650
- Stratix IV GX Devices 651
- Parameter Name 653
- Comments 653
- Custom PHY Width 659
- Chapter Document 661
- Changes Made 661
- Date Document 676
- How to Contact Altera 702
Relacionado con productos y manuales para Instrumentos de medición Altera Transceiver PHY IP Core
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales