Altera Stratix V Avalon-ST Manual de usuario Pagina 21
- Pagina / 293
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10.From the Simulation list, select ModelSim
®
. From the Format list, select the HDL language you
intend to use for simulation.
11.Click Next to display the Summary page.
12.Check the Summary page to ensure that you have entered all the information correctly.
13.Click Finish to create the Quartus II project.
14.Before compiling, you must assign I/O standards to the pins of the device. Refer to Making Pin
Assignments to Assign I/O Standard to Serial Data Pins for instructions.
15.You must connect the pin_perst reset signal to the correcsponding nPERST pin of the device. Refer to
the definition of pin_perst in the Reset, Status, and Link Training Signals section for more informa‐
tion.
16.Next, set the value of the test_in bus to a value that is compatible for hardware testing. In Qsys design
example provided, test_in is a top-level port.
a. Comment out the test_in port in the top-level Verilog generated file.
b. Add the following declaration, wire[31:0] test_in, to the same top-level Verilog file.
c. Assign hip_ctrl_test_in = 32'hA8.
d. Connect test_in to hip_ctrl_test_in.
Refer to the definition of test_in in the Test Signals section for more information about the bits of the
test_in bus.
17.Add the Synopsys Design Constraint (SDC) shown in the following example below to the top-level
design file for your Quartus II project.
18.To compile your design using the Quartus II software, on the Processing menu, click Start Compila‐
tion. The Quartus II software then performs all the steps necessary to compile your design.
Example 2-1: Synopsys Design Constraints
create_clock -period “100 MHz” -name {refclk_pci_express}{*refclk_*}
derive_pll_clocks
derive_clock_uncertainty
# PHY IP reconfig controller constraints
# Set reconfig_xcvr clock
# Modify to match the actual clock pin name
# used for this clock, and also changed to have the correct period set
create_clock -period "125 MHz" -name {reconfig_xcvr_clk}{*reconfig_xcvr_clk*}
# HIP Soft reset controller SDC constraints
set_false_path -to [get_registers* altpcie_rs_serdes|fifo_err_sync_r[0]]
set_false_path -from [get_registers *sv_xcvr_pipe_native*] -to[get_registers
*altpcie_rs_serdes|*]
# Hard IP testin pins SDC constraints
set_false_path -from [get_pins -compatibilitly_mode *hip_ctrl*]
UG-01097_avst
2014.12.15
Compiling the Design in the Qsys Design Flow
2-7
Getting Started with the Stratix V Hard IP for PCI Express
Altera Corporation
Send Feedback
- User Guide 1
- Datasheet 2
- Features 3
- Interface 4
- Release Information 7
- Device Family Support 7
- UG-01097_avst 10
- 2014.12.15 10
- Debug Features 11
- IP Core Verification 11
- Recommended Speed Grades 12
- • All Development Kits 14
- PCI Express 15
- Qsys Design Flow 16
- Generating the Testbench 17
- Simulating the Example Design 18
- Directory Description 19
- Time TLP Type Payload 19
- TLP Header 19
- Modifying the Example Design 23
- Separate Component 24
- Generating the Qsys System 27
- Parameter Value 28
- Parameter Settings 38
- Parameter Value Description 39
- Device Capabilities 45
- Error Reporting 47
- Link Capabilities 48
- MSI and MSI-X Capabilities 49
- Slot Capabilities 50
- Power Management 51
- PHY Characteristics 52
- Avalon‑ST RX Interface 54
- Packet TLP 59
- Aligned Addresses 64
- Single Packet Per Cycle 67
- Avalon-ST TX Interface 70
- Data 0 Header 2 83
- Clock Signals 85
- ECRC Forwarding 90
- Error Signals 90
- Interrupts for Endpoints 91
- Completion Side Band Signals 93
- Signal Directi 94
- Description 94
- Related Information 101
- Parity Signals 102
- LMI Signals 103
- Signal Direction Description 104
- Altera Corporation 107
- Send Feedback 107
- Field and Bit Map 112
- 0134678951 112
- Bit(s) Field Description 113
- Power Management Signals 115
- 15 011623 8 2791213142431 117
- Transceiver Reconfiguration 118
- Serial Data Signals 119
- PIPE Interface Signals 123
- Test Signals 128
- Registers 129
- Altera-Defined VSEC Registers 137
- CvP Registers 138
- 2014.08.18 139
- Bits Register Description 142
- Reset and Clocks 145
- Example Design 146
- Hard IP for PCI Express 146
- Clock Domains 149
- Data Rate Frequency 150
- Clock Summary 152
- Interrupts 153
- MSI Interrupts 154
- Allocated 155
- Implementing MSI-X Interrupts 156
- Legacy Interrupts 158
- Interrupts for Root Ports 159
- Error Handling 160
- Physical Layer Errors 161
- Data Link Layer Errors 161
- Transaction Layer Errors 162
- Error Type Description 163
- Status Bit Conditions 166
- IP Core Architecture 168
- Hard IP for PCI Express 169
- Top-Level Interfaces 170
- Avalon-ST Interface 170
- Clocks and Reset 171
- Hard IP Reconfiguration 171
- Transaction Layer 172
- Configuration Space 173
- (Soft Logic) 175
- Altera FPGA 175
- Protocol Extensions Supported 179
- Data Link Layer 179
- Physical Layer 181
- TX Packets 182
- Supported Message Types 184
- INTX Messages 184
- Power Management Messages 185
- Error Signaling Messages 186
- Locked Transaction Message 187
- Slot Power Limit Message 187
- Vendor-Defined Messages 187
- Hot Plug Messages 188
- Receive Buffer Reordering 190
- Using Relaxed Ordering 192
- Throughput Optimization 195
- Throughput of Posted Writes 197
- Design Implementation 199
- CONF_DONE 200
- Endpoint Reset 200
- Root Port Reset 200
- SDC Timing Constraints 201
- Optional Features 203
- ECRC on the RX Path 204
- ECRC on the TX Path 205
- Subscribe 208
- Testbench and Design Example 212
- Root Port Testbench 215
- Chaining DMA Design Examples 215
- Root Complex 217
- Chaining DMA 217
- Hard IP for 217
- BAR/Address Map 220
- Memory BAR Mapping 221
- Bit Field Description 222
- Addr Register Name 222
- Offset to Base 225
- Descriptor Type Description 225
- Byte Address 225
- Bits[21:18] Bit[17] Bit[16] 226
- Descriptor Field Endpoint 226
- RC Access Description 226
- Test Driver Module 227
- DMA Write Cycles 228
- Shared Memory 229
- DMA Read Cycles 230
- Registers (BAR2) 231
- Root Port Design Example 232
- Root Port 233
- Variation 233
- (variation_name.v) 233
- Root Port BFM 234
- BFM Configuration Procedures 235
- BFM Request Interface 235
- BFM Memory Map 236
- Offset (Bytes) Description 238
- BFM Procedures and Functions 242
- Location altpcietb_bfm_rdwr.v 243
- Express address 244
- Shared Memory Constants 251
- Constant Description 252
- Location 257
- Debugging Simulations 269
- Debugging 270
- Setting Up Simulation 276
- Use Third-Party PCIe Analyzer 277
- BIOS Enumeration Issues 277
- Address[31:2] 278
- Figure A-6: I/O Read Request 280
- 7 6 5 4 3 2 1 0 284
- Core Config 8 4 1 284
- Additional Information 286
- Date Version Changes Made 287
- How to Contact Altera 290
- Typographic Conventions 291
- Visual Cue Meaning 292
Relacionado con productos y manuales para Instrumentos de medición Altera Stratix V Avalon-ST
Instrumentos de medición Altera 100G Development Kit, Stratix IV GT Edition Manual de usuario
(80 paginas)
(80 paginas)
Instrumentos de medición Altera 100G Development Kit, Stratix V GX Edition Manual de usuario
(76 paginas)
(76 paginas)
Instrumentos de medición Altera Arria II GX FPGA Development Board, 6G Edition Manual de usuario
(62 paginas)
(62 paginas)
Instrumentos de medición Altera Cyclone IV GX Transceiver Starter Board Manual de usuario
(40 paginas)
(40 paginas)
Instrumentos de medición Altera DSP Development Kit, Stratix V Edition Manual de usuario
(74 paginas)
(74 paginas)
Instrumentos de medición Altera Transceiver Signal Integrity Development Kit, Stra Manual de usuario
(42 paginas)
(42 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales