Altera POS-PHY Level 4 IP Core Manual de usuario Pagina 19
- Pagina / 142
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2: Getting Started 2–9
Compile the Design and Program a Device
December 2014 Altera Corporation POS-PHY Level 4 IP Core User Guide
9. In the New Test Bench Settings dialog box, enter the information described in
Table 2–2 on page 2–9 (refer also to Figure 2–6 on page 2–9). To enter the files
described in the table, browse to the files in your project.
Figure 2–6 on page 2–9 shows an example of the testbench settings whxen the
<variation_name> is example.
10. When you have entered the required information for your new testbench, click OK
in the New Test Bench Settings dialog box.
11. Click OK in the Test Benches dialog box and then click OK in the Settings dialog
box.
12. Click Tools > EDA Simulation Tool, and then click Run EDA RTL Simulation
Tool. The simulation now begins with your chosen simulation tool.
Compile the Design and Program a Device
You can use the Quartus II software to compile your design. Refer to Quartus II Help
for instructions on compiling your design.
Table 2–2. NativeLink Test Bench Settings
Parameter Setting and File Name
Test bench name <any name>
Top-level module in test bench tb
Design instance name in test bench <variation name>
Run for 100 ns
Test bench files <variation name>_tb.v
Figure 2–6. Example of New Test Bench Settings for NativeLink
- User Guide 1
- POS-PHY Level 4 IP Core 1
- 1. About This IP Core 3
- General Description 5
- Interfaces & Protocols 6
- IP Core Verification 7
- OpenCore Plus IP Evaluation 9
- 2. Getting Started 11
- Using the Parameter Editor 12
- Upgrading Outdated IP Cores 13
- Specify Parameters 15
- Simulate the Design 17
- 3. Parameter Settings 21
- LVDS Data Rate 22
- PLL Input Frequency 23
- Data Path Width 23
- Buffer Mode 23
- Basic Parameters 24
- Atlantic FIFO Buffer Clock 25
- Atlantic Interface Width 25
- Optional Features 26
- Transmitter Options 27
- Receiver Options 28
- Starving Starving Starving 29
- Starving Hungry Hungry 29
- Starving Satisfied Satisfied 29
- FIFO RAM Blocks 30
- Note to Table 3–5: 31
- Protocol Parameters 32
- Features 39
- Block Description 39
- ALTLVDS_RX IP Core 41
- Data Processor (rx_data_proc) 42
- Atlantic Buffers 43
- Individual Buffers 44
- Status Processor 45
- Notes to Figure 4–3: 46
- Note to Table 4–1: 47
- Notes to Figure 4–4: 48
- Requirements for rxsys_clk 49
- Reset Structure 50
- Error Flagging and Handling 50
- SPI-4.2 Protocol Errors 51
- Notes to Table 4–3: 53
- DIP-4 Marking 54
- Notes to Figure 4–8: 56
- Missing SOP 59
- Missing EOP 60
- Note to Table 4–7: 62
- Note to Table 4–8: 63
- Note to Table 4–9: 63
- Latency Information 68
- Data Processor (tx_data_proc) 74
- Status Bypass Port 77
- Clock Structure 78
- Multiple Clock Domain 79
- Notes to Figure 5–4: 80
- Note to Table 5–5: 88
- 6. Testbench 99
- Variation 100
- Receiver 100
- Receiver Testbench Examples 101
- 6–4 Chapter 6: Testbench 102
- Chapter 6: Testbench 6–5 103
- 6–6 Chapter 6: Testbench 104
- Chapter 6: Testbench 6–7 105
- 6–8 Chapter 6: Testbench 106
- A. Start-Up Sequence 107
- Troubleshooting 109
- Issues and Tips—Miscellaneous 111
- Separate PLLs 113
- Shared PLL 113
- "<rx_pll>" 114
- Note to Table C–1: 115
- D. Board Design 117
- Probe Points 118
- Spare Pins 119
- JTAG Scan Chain 119
- D–4 Appendix D: Board Design 120
- Design for Testability 120
- Introduction 121
- Static Alignment 125
- Dynamic Alignment 126
- Altera Solutions 126
- Dynamic Phase Alignment (DPA) 127
- AC Timing Analysis 128
- Budgets 129
- G. Conversion from v2.2.x 131
- Receiver Signals 132
- Transmitter Signals 134
- Additional Information 139
- Note to Table: 140
- Additional Information Info–3 141
- Typographic Conventions 141
- Info–4 Additional Information 142
Relacionado con productos y manuales para Instrumentos de medición Altera POS-PHY Level 4 IP Core
Instrumentos de medición Altera PowerPlay Early Power Estimator for Altera CPLDs Manual de usuario
(30 paginas)
(30 paginas)
Instrumentos de medición Altera QDRII SRAM Controller MegaCore Function Manual de usuario
(68 paginas)
(68 paginas)
Instrumentos de medición Altera RLDRAM II Controller MegaCore Function Manual de usuario
(62 paginas)
(62 paginas)
Instrumentos de medición Altera SerialLite III Streaming MegaCore Function Manual de usuario
(68 paginas)
(68 paginas)
Instrumentos de medición Altera Signal Integrity Development Kit, Stratix V GX Edi Manual de usuario
(52 paginas)
(52 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales