Altera PHY IP Core Guía de usuario Pagina 105
- Pagina / 626
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 2-66: Bit Reversal and Polarity Inversion
Name Direction Clock
Domain
Description
rx_std_byterev_ena[<n>-1:0]
Input Asynchro‐
nous
This control signal is available when the
PMA width is 16 or 20 bits. When asserted,
enables byte reversal on the RX interface.
Used if the MSB and LSB of the transmitted
data are erroneously swapped.
rx_std_bitrev_ena[<n>-1:0]
Input Asynchro‐
nous
When asserted, enables bit reversal on the
RX interface. Bit order may be reversed if
external transmission circuitry transmits the
most significant bit first. When enabled, the
receive circuitry receives all words in the
reverse order. The bit reversal circuitry
operates on the output of the word aligner.
tx_polinv[<n>-1:0]
Input Asynchro‐
nous
When asserted, the TX polarity bit is
inverted. Only active when TX bit polarity
inversion is enabled.
rx_polinv[<n>-1:0]
Input Asynchro‐
nous
When asserted, the RX polarity bit is
inverted. Only active when RX bit polarity
inversion is enabled.
rx_std_signaldetect[<n>-
1:0]
Output Asynchro‐
nous
When enabled, the signal threshold detection
circuitry senses whether the signal level
present at the RX input buffer is above the
signal detect threshold voltage. You can
specify the signal detect threshold using a
Quartus II Settings File (.qsf) assignment.
This signal is required for the PCI Express,
SATA and SAS protocols.
Related Information
• ATX PLL IP Core on page 3-6
• CMU PLL IP Core on page 3-24
• fPLL IP Core on page 3-15
• Ports and Parameters on page 6-24
• Transceiver PHY Reset Controller Interfaces on page 4-13
This section describes the top-level signals for the Transceiver PHY Reset Controller IP core.
• Analog Parameter Settings on page 8-1
2-74
Standard PCS Ports
UG-01143
2015.05.11
Altera Corporation
Implementing Protocols in Arria 10 Transceivers
Send Feedback
- 101 Innovation Drive 1
- San Jose, CA 95134 1
- Contents 2
- Device Transceiver Layout 9
- UG-01143 10
- 2015.05.11 10
- Transceiver Bank Architecture 22
- The GX Transceiver Channel 26
- The GT Transceiver Channel 27
- Receiver PMA 28
- DeserializerCDR 28
- Advanced Transmit (ATX) PLL 29
- Fractional PLL (fPLL) 29
- Calibration 30
- • Calibration on page 7-1 31
- • Arria 10 Device Datasheet 31
- Transceiver Design Flow 33
- Configure the PHY IP Core 35
- Generate the PHY IP Core 36
- Select the PLL IP Core 36
- Configure the PLL IP Core 38
- Generate the PLL IP Core 39
- Create Reconfiguration Logic 39
- Connect Datapath 40
- Compile the Design 40
- Verify Design Functionality 41
- Configuration 42
- Protocol Preset 42
- Transceiver Configuration 52
- PMA Parameters 54
- Parameters Value Description 58
- Enhanced PCS Parameters 60
- Standard PCS Parameters 70
- PCS Direct 77
- PMA Ports 80
- Name Direction Clock Domain 84
- Enhanced PCS Ports 85
- Name Bit Functionality 94
- Standard PCS Ports 99
- Name Direction Clock 105
- Description 105
- Related Information 105
- IP Core File Locations 106
- Interlaken 107
- Altera Corporation 108
- Send Feedback 108
- Reset Controller 118
- Design Example 121
- Parameter Value 122
- Ethernet 128
- Rate Match FIFO for GbE 134
- Parameters Value 139
- Transceivers 148
- Parameter Range 151
- Idle Deleted 155
- Before Deletion 155
- After Deletion 155
- 10GBASE-KR PHY IP Core 156
- Name Range Description 162
- Name Value Description 163
- 10GBASE-KR PHY Interfaces 164
- Avalon-MM Register Interface 170
- Creating a 10GBASE-KR Design 192
- Simulation Support 194
- Item Description 195
- Native PHY 197
- Clock and Reset Interfaces 198
- 1G/10GbE PHY Interfaces 206
- Register Definitions 214
- Bit R/W Name Description 215
- Addr Bit R/W Name Description 233
- Creating a 1G/10GbE Design 239
- Design Guidelines 240
- Channel Placement Guidelines 240
- XAUI PHY IP Core 242
- XAUI Supported Features 245
- XAUI PHY Release Information 247
- Device Family Support 248
- Parameterizing the XAUI PHY 249
- XAUI PHY Ports 251
- XAUI PHY Interfaces 251
- Soft PCS 253
- Acronyms 258
- PCI Express (PIPE) 259
- Supported PIPE Features 260
- Gen1/Gen2 Features 261
- Power States Description 262
- Gen3 Features 266
- PCIe Gen3 Capability 267
- Mode Enabled 267
- Gen1 Gen2 Gen3 267
- • PIPE Design Example 275
- Gen1 PIPE Gen2 PIPE Gen3 PIPE 277
- Native PHY IP Ports for PIPE 285
- Figure 2-92: x4 Configuration 294
- Figure 2-93: x8 Configuration 295
- TX PLL Selection for CPRI 300
- Auto-Negotiation 300
- Supported Features for CPRI 301
- Other Protocols 310
- TX Bit Slip 320
- TX Polarity Inversion 320
- RX Bit Slip 320
- RX Polarity Inversion 321
- Word Aligner Manual Mode 323
- RX Bit Reversal 328
- RX Byte Reversal 329
- Parameter Value Description 330
- 8B/10B Encoder and Decoder 333
- 8B/10B TX Disparity Control 334
- TX Bit Reversal 336
- TX Byte Reversal 336
- Arria 10 GT Channel Usage 344
- Transceiver PHY IP 345
- NativeLink Simulation Flow 354
- Define Control Signals Using 356
- Custom Simulation Flow 359
- How to Generate Scripts 361
- Simulator Simulation File Use 362
- PLLs and Clock Networks 364
- ATX PLL IP Core 369
- Parameter Range Description 370
- Parameters Range Description 378
- Instantiating CMU PLL IP Core 386
- CMU PLL IP Core 387
- Input Reference Clock Sources 390
- Receiver Input Pins 392
- Transmitter Clock Network 393
- GT Clock Lines 398
- Clock Generation Block 399
- Transmitter Standard PCS 404
- Transmitter PMA 404
- Clock Generation Block (CGB) 404
- Receiver Standard PCS 406
- Channel Bonding 407
- PMA and PCS Bonding 408
- Skew Calculations 410
- Using PLLs and Clock Networks 412
- Bonded Configurations 416
- Implementing PLL Cascading 420
- Mix and Match Example 422
- When Is Reset Required? 427
- How Do I Reset? 427
- Recommended Reset Sequence 428
- min 20 ns 429
- Status Signals 433
- Control Signals 433
- Arria 10 PMA Architecture 448
- Transmitter Buffer 449
- 85Ω, 100Ω, OFF 450
- Receiver 451
- Receiver Buffer 452
- High Data Rate Mode 454
- Receiver Equalization Modes 459
- Channel PLL 461
- CDR Lock Mode 462
- Loopback 463
- Transmitter Datapath 466
- Interlaken Frame Generator 468
- Interlaken CRC-32 Generator 468
- 0 0 066676767 469
- Pattern Generators 470
- S0 S1 S4 S5 S8 471
- PRBS Output 471
- Scrambler 472
- (tx_clkout) 474
- KR FEC Blocks 475
- Receiver Datapath 476
- Descrambler 477
- Interlaken Frame Synchronizer 477
- PRBS Error 478
- PRBS datain 478
- Interlaken CRC-32 Checker 479
- Enhanced PCS RX FIFO 479
- Case Word Input Output 482
- RX KR FEC Blocks 483
- Byte Serializer 485
- 8B/10B Encoder 487
- RX Polarity Inversion Feature 496
- Rate Match FIFO 496
- 8B/10B Decoder 497
- Byte Deserializer 499
- PIPE Interface 503
- Clock Data Recovery Control 504
- Reconfiguration 505
- Reconfiguration Features 507
- Configuration Files 510
- Bit Position Description 511
- Instance 512
- Arbitration 515
- Direct Reconfiguration Flow 517
- Maximum Pre-Emphasis Settings 518
- Address Bit Values 521
- Switching Transmitter PLL 523
- Switching Reference Clocks 524
- ATX Reference Clock Switching 525
- Ports and Parameters 528
- On-Die Instrumentation 535
- Address Bits Read / 536
- Feature Description 536
- Start Pattern Checker 543
- Embedded Debug Features 544
- Control and Status Registers 545
- PRBS Soft Accumulators 548
- ODI Acceleration Logic 549
- Unsupported Features 562
- Calibration Registers 564
- ATX PLL Calibration Registers 566
- Capability Registers 566
- Power-up Calibration 567
- User Recalibration 569
- Calibration Example 570
- Fractional PLL Recalibration 571
- CDR/CMU PLL Recalibration 571
- PMA Recalibration 571
- Check Calibration Status 574
- Analog Parameter Settings 575
- XCVR_A10_RX_LINK 578
- XCVR_A10_RX_TERM_SEL 579
- XCVR_VCCR_VCCT_VOLTAGE - RX 580
- CTLE Settings 580
- XCVR_A10_RX_ONE_STAGE_ENABLE 582
- VGA Settings 583
- XCVR_A10_RX_ADP_DFE_FXTAP 584
- XCVR_A10_TX_LINK 585
- XCVR_A10_TX_COMPENSATION_EN 586
- XCVR_VCCR_VCCT_VOLTAGE - TX 587
- XCVR_A10_TX_SLEW_RATE_CTRL 587
- Value Description 589
- Transmitter VOD Settings 593
- XCVR_A10_REFCLK_TERM_TRISTATE 594
- LVDS TRISTATE_ON/TRISTATE_OFF 595
- Assign To 595
- Reference clock pin 595
- Subscribe 596
- Chapter Document 607
- Changes Made 607
- Date Version Changes 626
Relacionado con productos y manuales para Software Altera PHY IP Core
Software Altera UG-01080 Guía de usuario
(702 paginas)
(702 paginas)
Software Altera PHY IP Core Guía de usuario
(230 paginas)
(230 paginas)
Software Altera UG-01080 Guía de usuario
(120 paginas)
(120 paginas)
Software Altera DE2-115 Guía de usuario
(107 paginas)
(107 paginas)
Software Altera UG-01080 Guía de usuario
(484 paginas)
(484 paginas)
Avago-technologies MegaRAID SATA 150-4 (523) manuales
Manuales del propietario y guías del usuario para Hardware Avago-technologies MegaRAID SATA 150-4 (523).
Ofrecemos 3 manuales en pdf Avago-technologies MegaRAID SATA 150-4 (523) para descargar gratis por tipos de documentos: Manual de usuario
Avago technologies MegaRAID SATA 150-4 (523) Manual de usuario (2 paginas)
Marca: Avago-technologies | Categoria: Hardware | Tamaño: 0.13 MB |
Tabla de contenidos
Avago technologies MegaRAID SATA 150-4 (523) Manual de usuario (20 paginas)
Marca: Avago-technologies | Categoria: Hardware | Tamaño: 0.79 MB |
Tabla de contenidos
Avago technologies MegaRAID SATA 150-4 (523) Manual de usuario (154 paginas)
Marca: Avago-technologies | Categoria: Hardware | Tamaño: 1.42 MB |
Tabla de contenidos
MegaRAID
1
Contents
9
Contents xi
11
Chapter 1
19
Overview
19
1-2 Overview
20
1-4 Overview
22
Chapter 2
23
Chapter 3
49
Utility and
49
• MS-DOS
65
• NetWare
65
Chapter 4
85
4.4.12 Exit
98
Chapter 5
103
Start the
103
5.2.2 Features
105
Chapter 6
131
Virtual Sizing
131
Expansion
131
Appendix A
135
MegaRAID Service
135
IX-2 Index
144
Index IX-3
145
IX-4 Index
146
Index IX-5
147
IX-6 Index
148
Index IX-7
149
IX-8 Index
150
Index IX-9
151
IX-10 Index
152
Más productos y manuales para Hardware Avago-technologies
| Modelos | Tipo de documento |
|---|---|
| MegaRAID SCSI 320-1 (520-1 CH) |
Manual de usuario
Avago Technologies MegaRAID SCSI 320-1 (520-1 CH) User Manual,
3 paginas
|
| MegaRAID SCSI 320-2E |
Manual de usuario
Avago Technologies MegaRAID SCSI 320-2E User Manual,
2 paginas
|
| MegaRAID SCSI 320-2E |
Manual de usuario
Avago Technologies MegaRAID SCSI 320-2E User Manual,
3 paginas
|
| MegaRAID SCSI 320-4X (531) |
Manual de usuario
Avago Technologies MegaRAID SCSI 320-4X (531) User Manual,
4 paginas
|
| AcceleRAID 150 |
Manual de usuario
Avago Technologies AcceleRAID 150 User Manual,
102 paginas
|
| eXtremeRAID 2000 |
Manual de usuario
Avago Technologies eXtremeRAID 2000 User Manual,
22 paginas
|
| eXtremeRAID 2000 |
Manual de usuario
Avago Technologies eXtremeRAID 2000 User Manual,
84 paginas
|
| LSI SAS 3080X-R |
Manual de usuario
Avago Technologies LSI SAS 3080X-R User Manual,
2 paginas
|
| eXtremeRAID 3000 |
Manual de usuario
Avago Technologies eXtremeRAID 3000 User Manual,
90 paginas
|
| LSI SAS 31601E |
Manual de usuario
Avago Technologies LSI SAS 31601E User Manual,
2 paginas
|
| LSI SAS 3442E-R |
Manual de usuario
Avago Technologies LSI SAS 3442E-R User Manual,
2 paginas
|
| LSI SAS 3041X-R |
Manual de usuario
Avago Technologies LSI SAS 3041X-R User Manual,
40 paginas
|
| LSI SAS 3801X |
Manual de usuario
Avago Technologies LSI SAS 3801X User Manual,
2 paginas
|
| LSI SAS 9205-8e |
Manual de usuario
Avago Technologies LSI SAS 9205-8e User Manual,
12 paginas
|
| LSI20320 |
Manual de usuario
Avago Technologies LSI20320 User Manual,
38 paginas
|
| LSI20320IE |
Manual de usuario
Avago Technologies LSI20320IE User Manual,
2 paginas
|
| LSI21320-R |
Manual de usuario
Avago Technologies LSI21320-R User Manual,
2 paginas
|
| LSI7102XP-LC |
Manual de usuario
Avago Technologies LSI7102XP-LC User Manual,
2 paginas
|
| LSI SAS 3041E-R |
Manual de usuario
Avago Technologies LSI SAS 3041E-R User Manual,
218 paginas
|
| LSI7202XP-LC |
Manual de usuario
Avago Technologies LSI7202XP-LC User Manual,
2 paginas
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales