Altera Arria V Avalon-ST Manual de usuario Pagina 62
- Pagina / 248
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Table 4-6: Reset Signals
Signal Direction Description
npor
Input Active low reset signal. In the Altera hardware example designs,
npor is the OR of pin_perst and local_rstn coming from the
software Application Layer. If you do not drive a soft reset signal
from the Application Layer, this signal must be derived from
pin_perst. You cannot disable this signal. Resets the entire IP
Core and transceiver. Asynchronous.
In systems that use the hard reset controller, this signal is edge,
not level sensitive; consequently, you cannot use a low value on
this signal to hold custom logic in reset. For more information
about the hard and soft reset controllers, refer to the Reset and
Clocks chapter.
reset_status
Output Active high reset status signal. When asserted, this signal
indicates that the Hard IP clock is in reset. The reset_status
signal is synchronous to the pld_clk clock and is deasserted only
when the npor is deasserted and the Hard IP for PCI Express is
not in reset (reset_status_hip = 0). You should use reset_
status to drive the reset of your application. This reset is used
for the Hard IP for PCI Express IP Core with the Avalon-ST
interface.
pin_perst
Input Active low reset from the PCIe reset pin of the device. pin_perst
resets the datapath and control registers. This signal is required
for Configuration via Protocol (CvP). For more information
about CvP refer to Configuration via Protocol (CvP).
Arria V have 1 or 2 instances of the Hard IP for PCI Express.
Each instance has its own pin_perst signal. You must connect
the pin_perst of each Hard IP instance to the corresponding
nPERST pin of the device. These pins have the following locations:
• nPERSTL0: bottom left Hard IP and CvP blocks
• nPERSTL1: top left Hard IP block
For example, if you are using the Hard IP instance in the bottom
left corner of the device, you must connect pin_perst to
nPERSL0.
For maximum use of the Arria V device, Altera recommends that
you use the bottom left Hard IP first. This is the only location
that supports CvP over a PCIe link.
Refer to the appropriate device pinout for correct pin assignment
for more detailed information about these pins. The PCI Express
Card Electromechanical Specification 2.0 specifies this pin
requires 3.3 V. You can drive this 3.3V signal to the nPERST*
2014.12.15
Reset Signals
4-25
Interfaces and Signal Descriptions
Altera Corporation
Send Feedback
- User Guide 1
- Datasheet 2
- Features 3
- Release Information 5
- Device Family Support 6
- Altera FPGA 7
- Arria V or Cyclone V FPGA 8
- Debug Features 10
- IP Core Verification 11
- Recommended Speed Grades 11
- Qsys Design Flow 15
- Generating the Testbench 17
- Simulating the Example Design 17
- Directory Description 18
- Modifying the Example Design 21
- Parameter Settings 24
- Parameter Value Description 25
- Link Capabilities 27
- Device Capabilities 28
- Error Reporting 30
- Slot Capabilities 31
- Power Management 32
- <n> 34
- Legacy Interrupt 37
- Application Layer 39
- Avalon‑ST RX Interface 39
- Signal Direction Description 40
- Packet TLP 43
- Aligned Addresses 47
- Avalon-ST TX Interface 50
- Clock Signals 61
- Reset Signals 61
- Hard IP Status 63
- Error Signals 66
- ECRC Forwarding 66
- Interrupts for Endpoints 67
- Completion Side Band Signals 68
- Signal Directi 69
- Description 69
- Field and Bit Map 78
- 0134678951 78
- LMI Signals 79
- Hard IP for PCIe 80
- Power Management Signals 82
- 15 011623 8 2791213142431 83
- Bits Field Description 84
- Serial Interface Signals 86
- 9 Ch 18 Ch 87
- Variant Data CMU Clock 88
- PIPE Interface Signals 91
- Test Signals 95
- Registers 100
- Altera Corporation 100
- Send Feedback 100
- 2014.12.15 101
- Altera-Defined VSEC Registers 104
- CvP Registers 105
- Bits Register Description 109
- Reset and Clocks 112
- Example Design 113
- Hard IP for PCI Express 113
- Clock Domains 116
- Data Rate Frequency 117
- Related Information 117
- Clock Summary 118
- Interrupts 119
- Figure 7-1: MSI Handler Block 120
- Allocated 121
- Implementing MSI-X Interrupts 122
- Legacy Interrupts 124
- Interrupts for Root Ports 125
- Error Handling 126
- Physical Layer Errors 127
- Data Link Layer Errors 127
- Transaction Layer Errors 128
- Error Type Description 129
- Status Bit Conditions 132
- IP Core Architecture 134
- Hard IP for PCI Express 135
- Top-Level Interfaces 136
- Avalon-ST Interface 136
- Clocks and Reset 136
- Hard IP Reconfiguration 137
- Transceiver Reconfiguration 137
- Transaction Layer 138
- Configuration Space 139
- Data Link Layer 140
- Physical Layer 142
- TX Packets 143
- Multi-Function Support 144
- Supported Message Types 146
- INTX Messages 146
- Power Management Messages 147
- Error Signaling Messages 148
- Locked Transaction Message 149
- Slot Power Limit Message 149
- Vendor-Defined Messages 149
- Hot Plug Messages 150
- Receive Buffer Reordering 152
- Using Relaxed Ordering 154
- Throughput Optimization 157
- Throughput of Posted Writes 159
- Design Implementation 161
- Making Pin Assignments 162
- Optional Features 163
- ECRC on the RX Path 164
- ECRC on the TX Path 165
- Subscribe 168
- Testbench and Design Example 171
- Root Port Testbench 174
- Chaining DMA Design Examples 174
- Root Complex 176
- Chaining DMA 176
- Hard IP for 176
- PCI Express 176
- BAR/Address Map 179
- Memory BAR Mapping 180
- Bit Field Description 181
- Addr Register Name 181
- Byte Address 184
- Offset to Base 184
- Descriptor Type Description 184
- Bits[21:18] Bit[17] Bit[16] 185
- Descriptor Field Endpoint 185
- RC Access Description 185
- Test Driver Module 186
- DMA Write Cycles 187
- Shared Memory 188
- DMA Read Cycles 189
- Registers (BAR2) 190
- Root Port Design Example 191
- Root Port 192
- Variation 192
- (variation_name.v) 192
- Root Port BFM 193
- BFM Configuration Procedures 194
- BFM Request Interface 194
- BFM Memory Map 195
- Offset (Bytes) Description 197
- BFM Procedures and Functions 201
- Location altpcietb_bfm_rdwr.v 202
- Express address 203
- Shared Memory Constants 210
- Constant Description 211
- Location 216
- Debugging Simulations 228
- Debugging 229
- Setting Up Simulation 232
- Use Third-Party PCIe Analyzer 234
- BIOS Enumeration Issues 234
- Address[31:2] 235
- Figure A-6: I/O Read Request 237
- 7 6 5 4 3 2 1 0 241
- Core Config 8 4 1 241
- Additional Information 243
- Date Version Changes Made 244
- How to Contact Altera 246
- Typographic Conventions 247
- Visual Cue Meaning 248
Relacionado con productos y manuales para Instrumentos de medición Altera Arria V Avalon-ST
Instrumentos de medición Altera DDR3 SDRAM High-Performance Controller and ALTMEMP Manual de usuario
(10 paginas)
(10 paginas)
Instrumentos de medición Altera DDR SDRAM High-Performance Controllers and ALTMEMP Manual de usuario
(140 paginas)
(140 paginas)
Instrumentos de medición Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual de usuario
(3 paginas)
(3 paginas)
Instrumentos de medición Altera Nios II Embedded Evaluation Kit Cyclone III Editio Manual de usuario
(80 paginas)
(80 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales