Altera 10-Gbps Ethernet MAC MegaCore Function Manual de usuario Pagina 53
- Pagina / 175
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5–8 Chapter 5: 1G/10GbE MAC Design Example
1G/10GbE Testbench
10-Gbps Ethernet MAC MegaCore Function User Guide February 2014 Altera Corporation
avalon_if_params_pkg.sv
A SystemVerilog HDL testbench that contains parameters to
configure the BFMs. Because the configuration is specific to
the DUT, you must not change the contents of this file.
avalon_st_eth_packet_monitor.sv
A SystemVerilog HDL testbench that monitors the Avalon-ST
transmit and receive interfaces.
eth_mac_frame.sv
A SystemVerilog HDL class that defines the Ethernet frames.
The avalon_driver.sv file uses this class.
eth_register_map_params_pkg.sv
A SystemVerilog HDL package that maps addresses to the
Avalon-MM control registers.
tb_run.tcl
A Tcl script that starts a simulation session in the ModelSim
simulation software.
tb.sv
The top-level testbench file. This file includes the customized
1G/10GbE design example, which is the device under test
(DUT), a client packet generator, and a client packet monitor
along with other logic blocks.
wave.do
A signal tracing macro script for use with the ModelSim
simulation software to display testbench signals.
Table 5–4. 1G/10GbE Testbench Files
File Name Description
- User Guide 1
- Contents 3
- Contents iv 4
- Chapter 8. Registers 5
- Chapter 9. Interface Signals 5
- 1. About This IP Core 7
- 1.2. Release Information 8
- 1.3. Device Family Support 9
- 1.4. IP Core Verification 10
- ■ Timestamping is enabled 12
- ■ ptp_1step is disabled 12
- 2.2. Design Flows 14
- 2.3.2. Simulate the IP Core 15
- 2.4.1. Specify Parameters 16
- 2.4.3. Simulate the System 17
- [1] register bit to 1 18
- 3. 10GbE MAC Design Examples 19
- 3.2.0.2. Base Addresses 22
- Table 3–5 on page 3–10 23
- Creating a New 10GbE Design 24
- 3.6. 10GbE Testbenches 26
- 3.6.3. 10GbE Testbench Files 27
- 10GbE Testbenches 28
- Notes to Table 3–6: 36
- 4.1. Software Requirements 39
- Altera FPGA 40
- Design Example 40
- 4.2.1. Base Addresses 41
- Figure 4–3. Testbench 43
- The <ip 44
- Simulator 45
- 5.2.2. Base Addresses 49
- 1G/10GbE Design Example Files 50
- 5.5. 1G/10GbE Testbench 51
- Testbench 52
- 1G/10GbE Testbench 53
- 5.5.4.2. Backplane-KR Mode 55
- 6.2.1. Base Addresses 62
- ModelSim Simulator 66
- 7. Functional Description 68
- Architecture 69
- 7.2. Interfaces 70
- 7.2.2. SDR XGMII 71
- 7.2.3. GMII 71
- 7.2.4. MII 71
- 7.3. Frame Types 72
- 7.4. Transmit Datapath 72
- 7.4.2. Address Insertion 73
- Note to Figure 7–5: 74
- 7.4.4. XGMII Encapsulation 75
- 7.4.6. SDR XGMII Transmission 76
- Figure 7–7. Endian Conversion 77
- 7.5. Receive Datapath 78
- 7.5.4. Address Checking 79
- 7.5.5. Frame Type Checking 79
- 7.5.6. Length Checking 80
- 7.5.7. CRC-32 and Pad Removal 81
- 7.5.8. Overflow Handling 82
- Congestion and Flow Control 83
- 7.7.2.1. PFC Frame Reception 86
- Figure 7–11. Fault Signaling 87
- 7.9. IEEE 1588v2 88
- IEEE 1588v2 89
- 7.9.1. Architecture 90
- 7.9.2. Transmit Datapath 91
- 7.9.3. Receive Datapath 92
- 7.9.4. Frame Format 92
- MAC Header 93
- Note to Figure 7–16: 94
- 8. Registers 95
- 8.1. MAC Registers 96
- 0x0C1. Bits 4 to 31 are 98
- 0x0C3. Bits 4 to 31 are 98
- Register Name Access 100
- Bits 4 to 31 are reserved 101
- register 111
- Name R/W Description 112
- 8.3. Register Initialization 113
- 8–20 Chapter 8: Registers 114
- Register Initialization 114
- Chapter 8: Registers 8–21 115
- 8–22 Chapter 8: Registers 116
- Chapter 8: Registers 8–23 117
- 8–24 Chapter 8: Registers 118
- Chapter 8: Registers 8–25 119
- 9. Interface Signals 120
- Note to Table 9–1: 121
- Note to Figure 9–2: 123
- Note to Figure 9–3: 123
- Notes to Figure 9–4: 124
- Note to Figure 9–5: 125
- 9.0.3. SDR XGMII 127
- Note to Figure 9–7: 128
- Note to Figure 9–8: 129
- 9.0.4. GMII Signals 130
- 9.0.5. MII Signals 130
- Note to Table 9–8: 136
- Note to Table 9–9: 139
- 1588v2 feature 142
- 10. Design Considerations 150
- 10GbE MAC XAUI/10G BASE-R PHY 151
- Reconfiguration Controller 151
- A. Frame Format 153
- Figure A–2. VLAN Frame Format 154
- A.3. Pause Frame 155
- Figure A–5. PFC Frame Format 156
- B. Time-of-Day (ToD) Clock 157
- B.4. Parameter Setting 158
- ■ Bits 20 to 31: Not used 160
- B.6.1. Adjusting ToD’s Drift 161
- C. Packet Classifier 162
- Classifier 163
- D. ToD Synchronizer 166
- D.2. Block Diagram 167
- D.4. ToD Synchronizer Signals 169
- Additional Information 171
- Info–2 Additional Information 172
- Document Revision History 172
- Additional Information Info–3 173
- How to Contact Altera 174
- Typographic Conventions 174
- Additional Information Info–5 175
Relacionado con productos y manuales para Instrumentos de medición Altera 10-Gbps Ethernet MAC MegaCore Function
Instrumentos de medición Altera Triple Speed Ethernet MegaCore Function Manual de usuario
(223 paginas)
(223 paginas)
Instrumentos de medición Altera 8B10B Encoder/Decoder MegaCore Function Manual de usuario
(32 paginas)
(32 paginas)
Instrumentos de medición Altera I/O Phase-Locked Loop (Altera IOPLL) IP Core Manual de usuario
(11 paginas)
(11 paginas)
Instrumentos de medición Altera Embedded Systems Development Kit, Cyclone III Edit Manual de usuario
(82 paginas)
(82 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales